bobgo2728 Posted April 12, 2009 Report Share Posted April 12, 2009 OK I was looking at the back of my mac mini and was told that I could use a fiber optic or toslink audio on there to hook into my surround sound. But I noticed it was not 5.1 at all. I could not also adjust the audio either. What is the deal here. Is my mac mini able to do 5.1 out of the ports? Quote Link to post Share on other sites
isteve Posted April 12, 2009 Report Share Posted April 12, 2009 Audio preferences are in system preferences / sound. I use optical out on my imac and a quick look in the audio/midi setup utility it shows 5.1 and 7.1 in the speaker configuration. Of course they are not accessible because I don't have a 5.1 system. But I also think you would need a 5.1 quicktime plug in or some kind os AC-3 decoder. Quote Link to post Share on other sites
bobgo2728 Posted April 13, 2009 Author Report Share Posted April 13, 2009 (edited) OK I am not seeing anything in Lep that shows any OS X audio stuff. my audio control panel is greyed out on the taskbar. I don't see anything in the sound control panel. it just says digital out and built in output. I don't see anything else. Edited April 13, 2009 by Buddy Holly Quote Link to post Share on other sites
nickayre Posted April 13, 2009 Report Share Posted April 13, 2009 Well I'm not sure if your speakers are like mine (i have the logitech z-500) but with mine all the audio control is grayed out because the audio is sent raw to the speaker system and the speakers doing all the 5.1 surround. If on a pc where on the back you have all the colored ports I think there are like 5 or something this is because the audio is being processed (not sure if that's the correct word to use) on board and then sent out.I think this is whats going on, I could be wrong this is only from what I picked up. Quote Link to post Share on other sites
bobgo2728 Posted April 14, 2009 Author Report Share Posted April 14, 2009 ok the audio is being sent out raw? I would think there would be some way to change it over to PCM or what ever. It is going out via a toslink or optical into my 5.1 audio home receiver. It says it is getting a digital reception on the receiver. But I want the audio to be 5.1 all the time not 2 channel and then when I play DVD's it is 5.1. Quote Link to post Share on other sites
iccaros Posted April 14, 2009 Report Share Posted April 14, 2009 ok the audio is being sent out raw? I would think there would be some way to change it over to PCM or what ever. It is going out via a toslink or optical into my 5.1 audio home receiver. It says it is getting a digital reception on the receiver. But I want the audio to be 5.1 all the time not 2 channel and then when I play DVD's it is 5.1.PCM is RAW... Also you have to set up audio on most DVD's to do 5.1 as they revert to stereo for default. also are you sending this audio to a TV then to a separate audio system.. if so under HDCP processing stereo is all you get. Quote Link to post Share on other sites
isteve Posted April 14, 2009 Report Share Posted April 14, 2009 OK I am not seeing anything in Lep that shows any OS X audio stuff. my audio control panel is greyed out on the taskbar. I don't see anything in the sound control panel. it just says digital out and built in output. I don't see anything else.Do a spotlight search for Audio Midi you will get the Audio Midi Setup utility. Check the properties for output, speaker configuration.And Taskbar = Menubar, Control panel=System Preferences. Quote Link to post Share on other sites
bobgo2728 Posted April 14, 2009 Author Report Share Posted April 14, 2009 OK I did that and in there I set it for Multi Channel. it says source digital out and only gave me two channels to work with. I am sending this audio out of my mac mini to my 5.1 A/V receiver that is using optical or toslink. So why no surround?Do a spotlight search for Audio Midi you will get the Audio Midi Setup utility. Check the properties for output, speaker configuration.And Taskbar = Menubar, Control panel=System Preferences. Quote Link to post Share on other sites
isteve Posted April 14, 2009 Report Share Posted April 14, 2009 I don't know much about multi channel out I did have a M-Audio 7.1 card in my old G4 that came with 7.1 driver and a codec pack.I think what you need is a quicktime plugin that can decode the type of 5.1 audio that your dvd use. Maybe the AC-3 plugin. Quote Link to post Share on other sites
iccaros Posted April 14, 2009 Report Share Posted April 14, 2009 see thishttp://geekwithfamily.com/2007/07/05/home-...icktime-player/ Quote Link to post Share on other sites
isteve Posted April 14, 2009 Report Share Posted April 14, 2009 Good find, I have Perian on my macs and never even knew it did the dolby 5.1. Quote Link to post Share on other sites
bobgo2728 Posted April 14, 2009 Author Report Share Posted April 14, 2009 OK I will give this a shot. I think it is so wrong that Apple does not allow this. Quote Link to post Share on other sites
iccaros Posted April 14, 2009 Report Share Posted April 14, 2009 I understand the frustration... but remember its not that they are not allowing... you must have a HDCP approved Codex to do 5.1 (or better) and that is a licencing fee. My Dell does not do 5.1 either with out a plugin the same as the apple. it says 5.1 on everything.. but does not put it out.. I blame the MPAA and RIAA for all of the copywrite protection. but frustration noted and I believe Apple should have a help on their site that tells you how to do this. Quote Link to post Share on other sites
bobgo2728 Posted April 14, 2009 Author Report Share Posted April 14, 2009 OK I just hit a snag here. I installed and did everything except the plist edit. I can't find that file it speaks of. What is the deal? Quote Link to post Share on other sites
iccaros Posted April 15, 2009 Report Share Posted April 15, 2009 try a spotlight search of com.cod3r.a52codec.plist Quote Link to post Share on other sites
iccaros Posted April 15, 2009 Report Share Posted April 15, 2009 reading the comments found this..I followed the steps and ran into the same problem finding the plist file in leopard. I looked around a little bit, and found that you dont need perian or to change the midi settings at all. In fact, you can turn on Dolby Digital passthrough and get that nice little red dolby digital light (if you have an onkyo amp) by going to the preferences while in the dvd player, it has to be stopped first, and under “disc setup” the audio options at the bottom allow you specify which output you want…and select whatever is appropriate.Hope that helps anyone with leopard!# Kyle Kolbe Says:December 20th, 2007 at 8:33 amIn Leopard, I’ve settled on Mplayer (1.0rc2 latest svn build, you need X11 installed for it to work). You can set Mplayer’s prefs with a command line to passthrough AC3 and DTS signals from a Mac’s optical output. In Mplayer’s prefs-additional parameters add“-ac hwac3,hwdts,”I think, I have to double check. Only way I’ve been able to get true surround sound out of MKV files on the Macbook Pro.# Andre Lorentsen Says:December 31st, 2007 at 5:25 pmFollowed the steps and can confirm that this works perfectly under Leopard. The plist file is in your home library folder.The tip from Kyle Kolbe also works for mplayer 1.0rc2. Quote Link to post Share on other sites
bobgo2728 Posted April 15, 2009 Author Report Share Posted April 15, 2009 still not finding it for some reason but I will keep looking. Is that only allowed on mac book pros? Quote Link to post Share on other sites
bobgo2728 Posted April 29, 2009 Author Report Share Posted April 29, 2009 OK I am confused here. What are you trying to tell me here?reading the comments found this..I followed the steps and ran into the same problem finding the plist file in leopard. I looked around a little bit, and found that you dont need perian or to change the midi settings at all. In fact, you can turn on Dolby Digital passthrough and get that nice little red dolby digital light (if you have an onkyo amp) by going to the preferences while in the dvd player, it has to be stopped first, and under “disc setup” the audio options at the bottom allow you specify which output you want…and select whatever is appropriate.Hope that helps anyone with leopard!# Kyle Kolbe Says:December 20th, 2007 at 8:33 amIn Leopard, I’ve settled on Mplayer (1.0rc2 latest svn build, you need X11 installed for it to work). You can set Mplayer’s prefs with a command line to passthrough AC3 and DTS signals from a Mac’s optical output. In Mplayer’s prefs-additional parameters add“-ac hwac3,hwdts,”I think, I have to double check. Only way I’ve been able to get true surround sound out of MKV files on the Macbook Pro.# Andre Lorentsen Says:December 31st, 2007 at 5:25 pmFollowed the steps and can confirm that this works perfectly under Leopard. The plist file is in your home library folder.The tip from Kyle Kolbe also works for mplayer 1.0rc2. Quote Link to post Share on other sites
iccaros Posted April 29, 2009 Report Share Posted April 29, 2009 this was a comment on that page that showed that the file did not exists in Leopard. the went to the preferences of DVD player to set it. Quote Link to post Share on other sites
bobgo2728 Posted April 29, 2009 Author Report Share Posted April 29, 2009 OK then I should delete the plugin that I installed? Quote Link to post Share on other sites
iccaros Posted April 29, 2009 Report Share Posted April 29, 2009 sure.. Quote Link to post Share on other sites
bobgo2728 Posted April 29, 2009 Author Report Share Posted April 29, 2009 OK then. I mean I would like to know if stuff works anymore.sure.. Quote Link to post Share on other sites
iccaros Posted May 2, 2009 Report Share Posted May 2, 2009 I have to hook mine back up, but if you can set the settings in the dvd player I would assume you do not need the plug in. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.