garmanma Posted September 12, 2007 Report Share Posted September 12, 2007 (edited) Running dual boot with 2 drives. When I went to the hospital, my computer was left on and we had a bad electrical storm and power outage( I know, no lectures). I went to start it up, the Linux drive(slave) didn't show in the BIOS and it wouldn't boot to Windows. I removed the slave drive and used the recovery console to fixmbr and I'm now back up on Windows. I understand that Linux doesn't like to be abruptly shut down. I'm going to play around with it more tomorrow. Do you think the drive's trashed or salvageable?Mark Edited September 12, 2007 by garmanma Quote Link to post Share on other sites
shanenin Posted September 12, 2007 Report Share Posted September 12, 2007 Linux just like windows, prefers to be shut down properly. I don't think it is more sensitive then Windows is. Since you can't see the drive in the bios, that is not a file system corruption problem, but a hardware problem. The drive is probably just bad, but I would try pulling the battery and clearing the cmos. Quote Link to post Share on other sites
iccaros Posted September 13, 2007 Report Share Posted September 13, 2007 try a live linux cd and run fsck on the disk.. it should fix any issues. you may have to run the fsck for your format type (fsck.ext2 for example)Namefsck - check and repair a Linux file systemSynopsisfsck [ -sAVRTNP ] [ -C [ fd ] ] [ -t fstype ] [filesys ... ] [--] [ fs-specific-options ]Descriptionfsck is used to check and optionally repair one or more Linux file systems. filesys can be a device name (e.g. /dev/hdc1, /dev/sdb2), a mount point (e.g. /, /usr, /home), or an ext2 label or UUID specifier (e.g. UUID=8868abf6-88c5-4a83-98b8-bfc24057f7bd or LABEL=root). Normally, the fsck program will try to handle filesystems on different physical disk drives in parallel to reduce the total amount of time needed to check all of the filesystems.If no filesystems are specified on the command line, and the -A option is not specified, fsck will default to checking filesystems in /etc/fstab serially. This is equivalent to the -As options.The exit code returned by fsck is the sum of the following conditions:0 - No errors1 - File system errors corrected2 - System should be rebooted4 - File system errors left uncorrected8 - Operational error16 - Usage or syntax error32 - Fsck canceled by user request128 - Shared library errorThe exit code returned when multiple file systems are checked is the bit-wise OR of the exit codes for each file system that is checked.In actuality, fsck is simply a front-end for the various file system checkers (fsck.fstype) available under Linux. The file system-specific checker is searched for in /sbin first, then in /etc/fs and /etc, and finally in the directories listed in the PATH environment variable. Please see the file system-specific checker manual pages for further details.Options-s Serialize fsck operations. This is a good idea if you are checking multiple filesystems and the checkers are in an interactive mode. (Note: e2fsck(8) runs in an interactive mode by default. To make e2fsck(8) run in a non-interactive mode, you must either specify the -p or -a option, if you wish for errors to be corrected automatically, or the -n option if you do not.) -t fslist Specifies the type(s) of file system to be checked. When the -A flag is specified, only filesystems that match fslist are checked. The fslist parameter is a comma-separated list of filesystems and options specifiers. All of the filesystems in this comma-separated list may be prefixed by a negation operator 'no' or '!', which requests that only those filesystems not listed in fslist will be checked. If all of the filesystems in fslist are not prefixed by a negation operator, then only those filesystems listed in fslist will be checked. Options specifiers may be included in the comma-separated fslist. They must have the format opts=fs-option. If an options specifier is present, then only filesystems which contain fs-option in their mount options field of /etc/fstab will be checked. If the options specifier is prefixed by a negation operator, then only those filesystems that do not have fs-option in their mount options field of /etc/fstab will be checked. For example, if opts=ro appears in fslist, then only filesystems listed in /etc/fstab with the ro option will be checked. For compatibility with Mandrake distributions whose boot scripts depend upon an unauthorized UI change to the fsck program, if a filesystem type of loop is found in fslist, it is treated as if opts=loop were specified as an argument to the -t option. Normally, the filesystem type is deduced by searching for filesys in the /etc/fstab file and using the corresponding entry. If the type can not be deduced, and there is only a single filesystem given as an argument to the -t option, fsck will use the specified filesystem type. If this type is not available, then the default file system type (currently ext2) is used. -A Walk through the /etc/fstab file and try to check all file systems in one run. This option is typically used from the /etc/rc system initialization file, instead of multiple commands for checking a single file system. The root filesystem will be checked first unless the -P option is specified (see below). After that, filesystems will be checked in the order specified by the fs_passno (the sixth) field in the /etc/fstab file. Filesystems with a fs_passno value of 0 are skipped and are not checked at all. Filesystems with a fs_passno value of greater than zero will be checked in order, with filesystems with the lowest fs_passno number being checked first. If there are multiple filesystems with the same pass number, fsck will attempt to check them in parallel, although it will avoid running multiple filesystem checks on the same physical disk. Hence, a very common configuration in /etc/fstab files is to set the root filesystem to have a fs_passno value of 1 and to set all other filesystems to have a fs_passno value of 2. This will allow fsck to automatically run filesystem checkers in parallel if it is advantageous to do so. System administrators might choose not to use this configuration if they need to avoid multiple filesystem checks running in parallel for some reason --- for example, if the machine in question is short on memory so that excessive paging is a concern. -C [ "fd" ] Display completion/progress bars for those filesystem checkers (currently only for ext2 and ext3) which support them. Fsck will manage the filesystem checkers so that only one of them will display a progress bar at a time. GUI front-ends may specify a file descriptor fd, in which case the progress bar information will be sent to that file descriptor. -N Don't execute, just show what would be done. -P When the -A flag is set, check the root filesystem in parallel with the other filesystems. This is not the safest thing in the world to do, since if the root filesystem is in doubt things like the e2fsck(8) executable might be corrupted! This option is mainly provided for those sysadmins who don't want to repartition the root filesystem to be small and compact (which is really the right solution). -R When checking all file systems with the -A flag, skip the root file system (in case it's already mounted read-write). -T Don't show the title on startup. -V Produce verbose output, including all file system-specific commands that are executed. fs-specific-options Options which are not understood by fsck are passed to the filesystem-specific checker. These arguments must not take arguments, as there is no way for fsck to be able to properly guess which arguments take options and which don't. Options and arguments which follow the -- are treated as file system-specific options to be passed to the file system-specific checker. Please note that fsck is not designed to pass arbitrarily complicated options to filesystem-specific checkers. If you're doing something complicated, please just execute the filesystem-specific checker directly. If you pass fsck some horribly complicated option and arguments, and it doesn't do what you expect, don't bother reporting it as a bug. You're almost certainly doing something that you shouldn't be doing with fsck.Options to different filesystem-specific fsck's are not standardized. If in doubt, please consult the man pages of the filesystem-specific checker. Although not guaranteed, the following options are supported by most file system checkers:-a Automatically repair the file system without any questions (use this option with caution). Note that e2fsck(8) supports -a for backwards compatibility only. This option is mapped to e2fsck's -p option which is safe to use, unlike the -a option that some file system checkers support. -n For some filesystem-specific checkers, the -n option will cause the fs-specific fsck to avoid attempting to repair any problems, but simply report such problems to stdout. This is however not true for all filesystem-specific checkers. In particular, fsck.reiserfs(8) will not report any corruption if given this option. fsck.minix(8) does not support the -n option at all. -r Interactively repair the filesystem (ask for confirmations). Note: It is generally a bad idea to use this option if multiple fsck's are being run in parallel. Also note that this is e2fsck's default behavior; it supports this option for backwards compatibility reasons only. -y For some filesystem-specific checkers, the -y option will cause the fs-specific fsck to always attempt to fix any detected filesystem corruption automatically. Sometimes an expert may be able to do better driving the fsck manually. Note that not all filesystem-specific checkers implement this option. In particular fsck.minix(8) and fsck.cramfs(8) does not support the -y option as of this writing.AuthorTheodore Ts'o ([email protected])Files/etc/fstab.Environment VariablesThe fsck program's behavior is affected by the following environment variables:FSCK_FORCE_ALL_PARALLEL If this environment variable is set, fsck will attempt to run all of the specified filesystems in parallel, regardless of whether the filesystems appear to be on the same device. (This is useful for RAID systems or high-end storage systems such as those sold by companies such as IBM or EMC.) FSCK_MAX_INST This environment variable will limit the maximum number of file system checkers that can be running at one time. This allows configurations which have a large number of disks to avoid fsck starting too many file system checkers at once, which might overload CPU and memory resources available on the system. If this value is zero, then an unlimited number of processes can be spawned. This is currently the default, but future versions of fsck may attempt to automatically determine how many file system checks can be run based on gathering accounting data from the operating system. PATH The PATH environment variable is used to find file system checkers. A set of system directories are searched first: /sbin, /sbin/fs.d, /sbin/fs, /etc/fs, and /etc. Then the set of directories found in the PATH environment are searched. FSTAB_FILE This environment variable allows the system administrator to override the standard location of the /etc/fstab file. It is also useful for developers who are testing fsck.See Alsofstab(5), mkfs(8), fsck.ext2(8) or fsck.ext3(8) or e2fsck(8), cramfsck(8), fsck.minix(8), fsck.msdos(8), fsck.jfs(8), fsck.nfs(8), fsck.vfat(8), fsck.xfs(8), fsck.xiafs(8), reiserfsck(8).REFERENCED BY findfs(8), fs(5), jfs_tune(8), logsave(8), mkfs.minix(8), quotacheck(8), shutdown(8), tune2fs(8) Quote Link to post Share on other sites
garmanma Posted September 13, 2007 Author Report Share Posted September 13, 2007 Thanks guys. Iccaros, you just made my brain hurt more than eating a gallon of ice cream in 5 minutes. Talk about brain freeze. It definitely will be saved for later study. Mama said get a new drive, so who am I to argue I still haven't play with the drive anymore, maybe laterMark Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.