[Home Network Issue]

I would contact your isp and tell them you are unable to log into the dsl/router(assuming you rent it). They may replace it for you. Another solution would be to purchase an inexpensive 4 port router.

by any chance, are you using a cross over ethernet cable?

Regular bought cables.

It worked fine with these cables before, so I don't beleive it's a cable issue.

I'll call ISP, and probably wait for 2 hrs on the phone. They are terrible here.

Thanks much for all you help!

Email ****Edited for safety**** if there's anything I can ever do for you.

jbruced

I removed your email address to keep the internet gremlins from gettin' you.

Mike

I'm back with new info, I got connect to router/bridge (set up as bridge)

changed connection to dhcp and NO internet

this system worked before with same settings to the router, is it possibly IP changes by ISP?

jbruce

[Home Network Issue]

I would contact your isp and tell them you are unable to log into the dsl/router(assuming you rent it). They may replace it for you. Another solution would be to purchase an inexpensive 4 port router.

by any chance, are you using a cross over ethernet cable?

Regular bought cables.

It worked fine with these cables before, so I don't beleive it's a cable issue.

I'll call ISP, and probably wait for 2 hrs on the phone. They are terrible here.

Thanks much for all you help!

Email ****Edited for safety**** if there's anything I can ever do for you.

jbruced

I removed your email address to keep the internet gremlins from gettin' you.

Mike

[Home Network Issue]

I found that info using a manual that amazon.com furnished. I may have the info for a slightly different model. I would unplug the dsl line turn off your computer. Then power cycle the modem while the dsl line is still unplugged. Then turn on your computer. You may then be able to log in with that address.

Tried everything, direct to pc, with tel cable, w/o tel cable, through switch direct pc to router, reboot, reset switch, power off/on, will not connect (I found the manual online, says just what you said)

Aaaaaaaaaaaaargh

jbruced

[Home Network Issue]

From what I found on the web, that modem defaults to bridge mode. That means it is just passing through the ip address from your isp. That is why your computers are showing a 68.* ip address. You need to change the modem to router mode. You can do this using the web interface.

1. Plug your computer directly to the router using an ethernet cable.

2. enter the following address in your web browser http://192.168.1.1

3. The router should prompt you to enter a username and password. For both of these enter Admin note this is case sensitive.

4. under lan settings look around. Their is an option to enable your DHCP server. This will turn your modem into a router. Save your settings and everything should work.

Thanks for your effort.

Tried it all, may times, won't connect to router through http://192.168.1.1

jbruced

[Home Network Issue]

Nothing really makes sense. Every router I have ever seen, always assigns IP addresses on the 192.168.*.* range. The fact your PCs are getting addresses starting with 65 or 66 implies your dsl modem is not a router doing nat. You need a router doing nat for the setup you want.

Are both of your PCs setup to obtain an IP address using DHCP?

Yes both setup for DHCP

Both set to automatically obtain ip address. Don't know if ip is the issue here or not?

Still tearing hair out

Thanks!

jbruced

[Home Network Issue]

Nothing really makes sense. Every router I have ever seen, always assigns IP addresses on the 192.168.*.* range. The fact your PCs are getting addresses starting with 65 or 66 implies your dsl modem is not a router doing nat. You need a router doing nat for the setup you want.

Are both of your PCs setup to obtain an IP address using DHCP?

PCs are set up to automatically assign IP address.

There is a Paradyne dsl bridge/router (as listed on the label)

There is a dlink switch with 5 ports (used just to connect everything)

If I reboot with dls router disconnected, I get IPs starting with 169, and my network works perfectly.

Is the dsl router, or ISP for that matter screwing me up? I'm in the US Virgin Islands, and the ISP company is known for poor service.

Thanks!

jbruced

[Home Network Issue]

Welcome, and glad to have you.

When you say Smart Switch (hub) do you mean the Router?

First, try unplugging the hub and the DSL modem together. Wait 30 sec. and then plug them both back in. This should reset the DSL connection with the router.

Also, were you having problems before or after you installed ACT? If it was after you unintalled ACT, you could have unknowingly uninstalled components needed for connecting. Try creating a new connection

Hello and thank you for the reply.

Since my system works without the internet connected (through a paradyne dsl bridge/router that acts a direct connection according to my ISP), the dlink switch should be fully operational and virtually transparent to the system.

Tried unplugging everything at least 50 times, that's why I'm tearing my hair out .

By the way, both PCs access the internet with no problem through the switch and router.

Appreciate your interest!

jbruced

[Home Network Issue]

Hi all,

New here, so forgive any improper behavior, not intentional.

equipment configuration:

2 XP home computers

1 network smart switch(hub)

1 dsl box

all devices connected to network switch.

Problem:

When I disconnect dsl box from the network (unplug) and reboot computers, my home network works great.

When I reconnect dsl box to the network and reboot (or PC reconfigures it's ip for internet connection), I lose all connectivity between PCs, can't even see them in network workgroup. (Though I can ping both computers from each other)

Tryed a ton of network wizard setups, ipconfig release and renew, and a bunch of nststat commands (refresh etc..), and reboots to no avail.

I did notice one quirk, the first octet for each PCs ip address is not the same (65 and 66), they were the same as far as I remember (65 and 65) since I installed the network, until these recent problems

This happened after I installed and uninstalled ACT! , ACT! loads msSQL and other stuff too, these were all uninstalled and removed.

(This may be coincidental)

Tearing out hair , help will be HUGELY appreciated.

jbruced